Laserfiche WebLink
4.34 kW DC PV SOLAR SYSTEM - FLUSH MOUNTED <br />ep,17PTOVOLTAIC NOTES <br />O�ILF <br />ORAN AC f�10INAN INTERACTIVE PHOTOVOLTAIC SYSTEM SHALL AUTOMATIC ALL <br />DE-ENERGI E IT OUTP TOHE CONNECTED ELECTRICAL PRODUCTION AND DISTRIBUTION NETWORK UPON <br />LOSS O SYSTEM,AND SHALL REMAIN IN THAT STATE UNTIL THE ELECTRICAL <br />PRODUCTION IBUTION N WORK VOLTAGE HAS BEEN RESTORED. (NEC 690361) <br />2. ALL EXTERIOR ELECT ICAL MET LIC TUBING(EMT) CONDUIT FITTING SHALL BE RAIN TIGHT THREAD -LESS <br />COMPRESSION"ApE"+� 7 <br />3. MODULES AND SUPPORT ST Y�RES SHALL BE GROUNDED <br />4. NAM�PLAFES SHALL BE PROV,I FOR ALL CIRCUITS IN THE SERVICE DISTRIBUTION AND POWER <br />DISTRIbN SSA/ITCH BOARDS`_ NEL BOARDS, DISCONNECTING SWITCHES, TERMINAL CABINETS, ETC. ALL <br />NAMEPLA ilj,SHALL BE PERMANENTLY ATTACHED AND BE OF SUFFICIENT CAPACITY TO WITHSTAND THE <br />WEATHER. I . D <br />5. JUNCTION BOX/COMBINER BOX HAVE TO USE COMPRESSION TYPE STRAIN RELIEF POSITIONED FOR <br />APPROPRIATE WATER RUN OFF <br />6. CONDUIT RUNS SHALL BE PROVIDED WITH SUFFICIENT WEATHERPROOF PULL BOXES OF JUNCTION <br />BOXICOMBINER BOXES PER APPROPRIATE NEC REQUIREMENTS. <br />7. SEE PROVIDED CUT SHEETS FOR ADDITIONAL EQUIPMENT SPECIFICATIONS <br />8. WIRING MATERIALS SHALL BE SUITABLE FOR THE SUN EXPOSURE AND WET LOCATIONS. FIELD <br />APPLIED PROTECTIVE COATINGS ARE NOT ACCEPTABLE. <br />9. JUNCTION, PULL AND OUTLET BOXES LOCATED BEHIND MODULES SHALL BE SO INSTALLED THAT THE <br />WIRING CONTAINED IN THEM CAN BE RENDERED ACCESSIBLE DIRECTLY OR BY DISPLACEMENT OF <br />MODULE(S) SECURED BY REMOVABLE FASTENERS AND CONNECTED BY A FLEXIBLE WIRING SYSTEM. <br />(NEC 690.34) <br />10. IN AN UNDERGROUND PHOTOVOLTAIC SYSTEM, THE POWER SOURCE SHALL BE LABELED WITH THE <br />FOLLOWING WARNING AT EACH JUNCTION BOX, COMBINER BOX, DISCONNECT AND DEVICE WHERE THE <br />UNGROUNDED CIRCUITS MAY BE EXPOSED DURING SERVICE: "WARNING - ELECTRIC SHOCK HAZARD. <br />THE CURRENT CIRCUIT CONDUCTORS OF THIS PHOTOVOLTAIC POWER SYSTEM ARE UNGROUNDED BUT <br />MAY BE ENERGIZED WITH THE RESPECT TO GROUND DUE TO LEAKAGE PATHS AND/OR GROUND <br />FAULTS." (NECE 690.35(F)) <br />11. ALL PHOTOVOLTAIC MODULES AND ASSOCIATED EQUIPMENT AND WIRING MATERIAL SHALL BE <br />PROTECTED FROM ANY PHYSICAL DAMAGE. <br />12. ALL ELECTRICAL DEVICES AND UTILIZATION EQUIPMENT SHALL BE LISTED BY AN APPROVED TESTING <br />AGENCY. <br />13. OUTDOOR EQUIPMENT SHALL BE AT LEAST NEMA 3R RATED. <br />14. ALL SPECIFIED WIRING IS BASED ON THE USE OF COPPER <br />15. CONTRACTOR SHALL OBTAIN ELECTRICAL PERMITS AND SHALL COORDINATE ALL INSPECTION, <br />COMMISSIONING AND ACCEPTANCE WITH THE CLIENT, UTILITY CO. AND CITY INSPECTORS AS NEEDED <br />16. DRAWINGS ARE DIAGRAMMATIC ONLY, ROUTING OF RACEWAYS SHALL BE AT THE OPTION OF THE <br />CONTRACTOR UNLESS OTHERWISE NOTED AND SHALL BE COORDINATED WITH OTHER TRADES. <br />17. IF DISTANCES OF CABLE RUNS ARE DIFFERENT THAN SHOWN, THE CONTRACTOR SHALL NOTIFY <br />ELECTRICAL ENGINEER TO VALIDATE THE WIRE SIZE. FINAL DRAWINGS WILL BE RED -LINED AND UPDATED <br />AS APPROPRIATE, <br />18. WHENEVER A DISCREPANCY IN QUANTITY OF EQUIPMENT, ARISES ON THE DRAWINGS OR <br />SPECIFICATIONS, THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING AND INSTALLING ALL <br />MATERIAL AND SERVICES REQUIRED BY THE STRICTEST CONDITIONS NOTED ON THE DRAWINGS OR IN <br />THE SPECIFICATIONS TO ENDURE COMPLETE COMPLIANCE AND LONGEVITY OF THE OPERABLE SYSTEM <br />REQUIRED BY THE ARCHITECT/ENGINEER. <br />19. ALL BROCHURES, OPERATION MANUALS, CATALOGS, SHOP DRAWINGS, ETC. SHALL BE HANDED <br />OVER TO THE OWNER'S REPRESENTATIVE AT THE COMPLETION OR WORK. <br />20. ALL WIRING CONCEALED IN WALL AND CEILING SPACES SHALL BE IN METAL CONDUIT. <br />21. THE SEISMIC BRACING AND ANCHORAGE OF ELECTRICAL CONDUITS SHALL BE IN ACCORDANCE <br />WITH THE "SMACNA"-GUIDLINES FOR SEISMIC RESTRAINS OF MECHANICAL SYSTEMS AND PLUMING <br />PIPING SYSTEMS. <br />22. ALL OF THE LISTED SYSTEMS REQUIRED THAT THE SEISMIC LATERAL FORCE F INCLUDING <br />CONSIDERATION OF aAP AND OP BE DETERMINED AT EACH LEVEL OF THE BUILDING SO THAT BRACE <br />SPACING CAN BE CALCULATED. THE DISTRICT STRUCTURAL ENGINEER CAN APPROVE THE SEISMIC <br />LATERAL FORCE DETERMINATION. <br />23. A COPY OF THE CHOSEN BRACING SYSTEM(S) INSTALLATION GUIDE/MANUAL SHALL BE ON THE JOB <br />SITE PRIOR TO STARTING THE INSTALLING OF HANGERS AND/OR BRACES. <br />24. WHEN INSTALLING DRILLED -IN ANCHORS AND/OR POWDER DRIVEN PINS IN EXISTING <br />NON -PRESTRESSED REINFORCED CONCRETE, USE CARE AND CAUTION TO AVOID CUTTING OR <br />DAMAGING THE REINFORCED BARS. WHEN INSTALLING THEM INTO EXISTING PRE -STRESSED CONCRETE <br />TENDONS BY USING A NON-DESTRUCTIVE METHOD PRIOR TO INSTALLATION. EXERCISE EXTREME CARE <br />AND CAUTION TO AVOID CUTTING OR DAMAGING THE TENDONS DURING INSTALLATION. MAINTAIN A <br />MINIMUM CLEARANCE OF ONE INCH BETWEEN THE REINFORCEMENT AND THE DRILLED -IN ANCHOR. <br />25. THE WORKING CLEARANCES AROUND THE EXISTING ELECTRICAL EQUIPMENT AS WELL AS THE NEW <br />ELECTRICAL EQUIPMENT WILL BE MAINTAINED IN ACCORDANCE WITH NEC 110.26. <br />26. CONDUCTORS EXPOSED TO SUNLIGHT SHALL BE LISTED AS SUNLIGHT RESISTANT. (NEC 300.6 01, <br />310.8 D) <br />27. GROUNDING BUSHINGS ARE REQUIRED AROUND PRE -PUNCHED CONCENTRIC KNOCKOUTS ON THE <br />DC SIDE OF THE SYSTEM. (NEC 250.97) <br />28. THE GROUNDING ELECTRODE CONDUCTOR MUST BE PROTECTED FROM PHYSICAL DAMAGE IF <br />SMALLER THAN #6 COPPER WIRE. (NEC 250.64 B) <br />29. GROUNDING ELECTRODE CONDUCTOR WILL BE CONTINUOUS, EXCEPT FOR SPLICES OR JOINTS AT <br />BUSBARS WITHIN LISTED EQUIPMENT. (NEC 250.64 C) <br />30. RACEWAY FOR GROUNDING ELECTRODE CONDUCTOR SHALL BE BONDED AT EACH END. (CEC <br />250.64 (E) <br />31. WHERE ALL TERMINALS OF THE DISCONNECTING MEANS MAY BE ENERGIZED IN THE OPEN POSITION, <br />A SIGN WILL BE PROVIDED WARNING OF THE HAZARD PER NEC 690.17. 34. EACH UNGROUNDED <br />CONDUCTOR OF THE MULT-IWIRE BRANCH CIRCUIT WILL BE IDENTIFIED PER PHASE AND SYSTEM PER <br />NEC210.5. <br />32. CIRCUITS OVER 250V TO GROUND SHALL COMPLY WITH NEC250.97 & 250.92 (B) & LAMC 93.250.97. <br />33. DC CONDUCTORS EITHER DO NOT ENTER THE BUILDING OR ARE RUN IN METALLIC RACEWAYS OR <br />ENCLOSURES TO THE FIRST ACCESSIBLE DC DISCONNECTING MEANS PER NEC 690.31 (E), LAMC <br />93.690.31 (E) <br />34. ALL METALLIC FRAME RAILS AND OTHER CURRENT CARRYING METALLIC COMPONENTS (CONDUIT, <br />JUNCTION & PULL BOXES, RACEWAY, ETC) SHALL BE SOLIDLY GROUNDED PER THE MANUFACTURER'S <br />INSTALLATION INSTRUCTIONS LAMC 93.690.110.3 & 93.110.3(B). <br />35. SCREWS, NUTS, BOLTS & WASHERS THAT ATTACH EQUIPMENT GROUNDING LUGS SHALL BE <br />STAINLESS STEEL LAMC 93.110.3(B). <br />36. NO PIPING, DUCTS OR EQUIPMENT FOREIGN TO ELECTRICAL EQUIPMENT SHALL BE PERMITTED TO BE <br />LOCATED WITHIN THE DEDICATED SPACE ABOVE THE ELECTRICAL EQUIPMENT. <br />37. ALL FIELD INSTALLED JUNCTION, PULL AND OUTLET BOXED LOCATED BEHIND MODULES OR PANELS <br />SHALL BE ACCESSIBLE DIRECTLY OR BY DISPLACEMENT OF A MODULE (S) OR PANEL (S) SECURED BY <br />REMOVABLE FASTENERS. <br />38. REMOVAL OF A DWP-INTERACTIVE INVERTER OR OTHER EQUIPMENT SHALL NOT DISCONNECT THE <br />BONDING CONNECTION BETWEEN THE GROUNDING ELECTRODE CONDUCTOR AND THE PHOTOVOLTAIC <br />SOURCE AND/OR OUTPUT CIRCUIT GROUNDED CONDUCTOR. <br />39. THE ROOF MOUNTED PHOTOVOLTAIC MODULES, PANELS, OR SOLAR VOLTAIC ROLL ROOFING <br />MATERIAL SHALL HAVE THE SAME OR BETTER LISTED FIRE -RESISTANCE RATING THAN THE BUILDING <br />ROOF -COVERING MATERIAL. <br />40. ALL ROOF MOUNTED CONDUIT WILL BE A MINIMUM 1/2" OFF THE ROOF SURFACE. <br />Z) AERIAL VIEW <br />•2320 151h St, <br />Anacotles, WA 98221 m <br />Volunteer Park <br />VICINITY MAP <br />CITY OF ANACORTES <br />PLANNING AND BUILDING DEPT: <br />APPROVED PLANS <br />REVIEWED FOR CODE COMPLIANCE <br />PERMIT #: BLD-2021-0387 <br />ADDRESS: 2320 15T ST <br />APPROVED BY: <br />SUBJECT TO FIELD INSPECTION. APPROVED PL S SHALL NOT <br />BE ALTERED WITHOUT AUTHOR17 ON. <br />SCOPE OF WORK <br />INSTALLATION OF ROOF MOUNTED SOLAR PV SYSTEM <br />NEW EQUIPMENT: <br />14 HYPRO STP310S-20/WFB - 310 WATTS SUNTECH MODULES <br />3 HM-120ON HOYMILES MICROINVERTER <br />1 HM-60ON HOYMILES MICROINVERTER <br />0 HM-30ON HOYMILES MICROINVERTER <br />SYSTEM SIZE: <br />4.34 DC kW POWER RATING <br />4.20 AC kW POWER RATING <br />RACKING: <br />GRASOL RACKING SYSTEM FOR COMP ROOF <br />ARRAY AREA: 17.65 SQFT x 14 = 247.1 SQFT <br />SITE DETAIL 2018 code cycle <br />UTILITY: PUGET SOUND ENERGY <br />ROOF MATERIAL: COMP SHINGLE <br />ASCE 7 GROUND SNOW LOAD: 20 PSF <br />ASCE 7-10 WINDSPEEDS: (3 SEC GUST IN MPH) <br />RISK CATEGORY II: 110 <br />ODE AUTHORITY <br />201 SHINGTON STATE BUILDING CODE 5 IBC) 2015 <br />WASHIN N STATE ENERGY CODE IECC) 2015 <br />WASHINGTON TE RESIDENTI ODE(2015 INTERNATIONAL <br />RESIDENTIAL COD SHI ON AMENDMENTS 2014 <br />WAC51-51-2300 SECTI 02) 2020 WAC 296-46B (2020 NEC) 2017 <br />WASHINGTON CI ELECTR CODE (2017 WCEC) 2015 <br />WASHINGT TATE MECHANICAL E(2015 UMC) 2015 <br />WASHI ON STATE PLUMBING CODE ( UPC) 2015 <br />INGTON STATE FIRE CODE (2015 IFC) <br />SHEETINDEX <br />A-1 GENERAL NOTES & PROJECT DATA <br />A-2 SITE PLAN <br />A-3 WIRING & MOUNTING PLAN <br />E-1 ELECTRICAL SINGLE LINE DIAGRAM <br />E-2 ELECTRICAL CALCULATIONS <br />E-3 LABELING REQUIREMENTS <br />E-4 EQUIPMENT: PV MODULE SPECIFICATION SHEET <br />E-5 EQUIPMENT: MICROINVERTER SPECIFICATION SHEET <br />E-6 EQUIPMENT: MICROINVERTER SPECIFICATION SHEET <br />S-1 EQUIPMENT: RACKING - DATA SHEET <br />S-2 EQUIPMENT: RACKING - DATA SHEET <br />S-3 EQUIPMENT: RACKING - GROUNDING <br />infinity polar <br />INFINITY HOME SOLUTIONS <br />6405 E MILL PLAIN <br />VANCOUVER WA 98661 <br />PHONE:1-800-818-0598 <br />PROJECT DETAILS <br />4.34 DC kW <br />4.20kW CEC-AC RATED SYSTEM <br />MICROINVERTER SYSTEM <br />TILT: 180 AZIMUTH: 1800 <br />CUSTOMER INFO <br />RICHARD LOVEETT <br />2320 15TH ST <br />ANACORTES, WA 98221 <br />REVISION HISTORY <br />DATE I DESCRIPTION <br />5/17/2021 I Initial drawing - C. Brin <br />SHEET TITLE <br />GENERALNOTES <br />cx <br />PROJECT DATA <br />SHEET NUMBER <br />A-1 <br />